A floor made of sawn wood is a trendy finish option available for self-assembly. The floor from the saw cuts in the house is beautiful and environmentally friendly The floor from the end saw cuts of the tree

Before installing the floor, make sure that the wood saw cuts are well dried.

Materials:
Pieces of logs are about 10-12 cm thick (the diameter may differ from everyone's imagination).
Sawdust, limestone, clay, linseed oil, beeswax, water, lard.

Floor installation is similar to laying paving slabs.
Stages of work:
1) Prepare the floor. We fill it with river pebbles by about 7-8 cm.

3) When laying the saw cuts of a tree, we tap with a hammer and check with a level so that the floor is even. The distance between saw cuts should be from one to two centimeters.

4) We make a mixture for filling the joints: For a floor area of ​​​​about 5 square meters in a 15-liter bucket for 1 kg of melted pork fat, add 1 kg of lime, 5 kg of sawdust and 2 kg of clay with water. This mixture must be thoroughly mixed. You should get a pasty mass. You can also add marble dust to this mixture to make the mixture waterproof.

5) Rub the prepared mixture between saw cuts. We try to rub it in thoroughly so that no air remains inside, as cracks may occur later.

6) Leave the floor to dry for one or two days. After drying, we check if cracks appear, then cover them up and wait for complete drying again.

7) After complete drying, the floor must be leveled so that the surface is smooth (you can rent a scraping machine). Again, check the floor for cracks and chips. If they are, then cover them up.

8) We polish the floor. Since our floor is made of natural materials, we will polish it - beeswax and linseed oil. This will make the floor waterproof. If desired, you can cover the floor with various stains and varnishes, but these are all chemical compounds.

All buildings and structures (gazebo, terrace, swimming pool, greenhouse, vegetable garden and different elements landscape design) at the dacha or personal plot communicated through tracks.

What kind of path to make, or rather, from what material, everyone decides for himself, specifically in the framework of this article, we will consider the manufacture of a garden path from chopped tree rings.

Among all the options (from boards, timber, shields, garden parquet, branches and bamboo), one of the most accessible in terms of material and the most complex in terms of device is the paths from tree cuts. The material is structured according to the principle step by step instructions so that anyone can build such a path with their own hands.

A path made of wooden saw cuts can be called differently: from cuts, stumps (dice, block, stump, log, ends of logs), but the construction method will be identical.

Garden paths from saw cut wood - step by step guide

For work you will need materials and tools:

1. Saw cuts (cuts) of a tree
2. Roll waterproofing or geotextile (geotextile)
3. Sand, pebbles, gravel, water
4. Level
5. Hammer (preferably a mallet)
6. Chainsaw manual
7. Shovel, buckets, brushes

Step 1 - preparation of wooden saw cuts

You need to start work with the preliminary preparation of saw cuts (cuts) of the tree. Then they will be ready just in time for laying.

When choosing wood, you need to proceed from how long it is supposed to operate the track, and what load it will have. When arranging garden paths from tree cuts in the country, it is better to give preference to hardwoods. So, for example, oak will serve you for about ten years, pine - no more than seven. And larch is practically indestructible and will delight you for more than a quarter of a century.

But, most often, blanks for the track are made from those rocks that are available. It all depends on the budget, saw cuts from poplar will cost much less than from oak or larch.

To prepare the cut, you need to dissolve the log into pieces 150-200 mm high.

The rule works here, the larger the diameter of the log, the greater the saw cut height should be. And of course, the height of all blanks should be approximately the same.

If the thickness of the saw cut is less than 100 mm, there is a high probability that it will not be fixed in the ground, and may “pop out” when pressed.

To extend the life of the saw cut, it must be cleaned of bark. Because it is the bark that will begin to flake off first.

In addition, it is better to refuse to use saw cuts that have cracks. They will begin to deteriorate first of all and very quickly, and the crack may increase under the influence of loads on it.

The saw cut must also be pre-processed. The most common can be called drying oil treatment.

To do this, it is heated to a boiling state and the saw cut is completely coated. Please note that this work is dangerous, so it is better to buy special antiseptic solutions that will provide both moisture protection and biosecurity. In such a solution, the saw cut should be from two hours to two days.

To protect the wood from decay even more reliably, the bottom of the round timber must be additionally treated with bitumen. Wood can be aged with a solution of copper sulphate.

The treated saw cut must be dried well.

Step 2 - marking the track

The complexity of this step is in determining optimal sizes paths - 350 mm, sufficient width for one person to move freely. As well as its route - to provide access to all the required objects.

Step 3 - ground preparation

In order for wooden garden paths to serve you as long as possible and be safe, they must be securely fixed.

To do this, along the marked route of the future path, you need to dig a trench. Its depth depends on the length of the hemp (cut) plus 50-100 mm. (depending on the type of soil and the expected load on the track).

The width of the trench is equal to the desired width of the path.

A waterproofing film is laid on the bottom of the trench (you can apply polyethylene film used for greenhouses or geofabric).

Gravel or small gravel is poured over the film. This drainage is necessary in order to protect the wood from moisture. The height of the first layer of the cushion is half of the required height (25-50 mm). It is important to pack it well.

The sand and gravel cushion must be leveled using building level. This will significantly save time and effort when laying saw cuts.

Step 4 - installation of curbs for tracks (sides)

If a curb is provided, then they must be installed before the installation of saw cuts.

Stones, bricks, sheet iron, wooden blocks or long logs can be used as material for the curb.

But, in order not to disturb the harmony of the garden path, chibouks sawn along are used.

Step 5 - filling the second layer of sand cushion

Sand is used as the second layer. The total height of the pillow is 50-100 mm.

To compact the sand well, a technique such as watering it with water is used.

The material was prepared for the site www.site

Step 6 - scheme for laying saw cuts from wood

The order in which the wood slices are mounted is not critical. The formation of the pattern depends on the preferences of the owner.

It can be positioned so that there is as little space as possible between the cuts. And you can, on the contrary, arrange them widely.

The main thing at this stage is to slightly “drown” the saw cut (tamp it down), and also align them in level.

Step 7 - decorative design of a garden path from tree cuts

The space between the cuts can be covered with sand or earth mixed with seeds of ground cover plants.

And leave the cuts themselves in their original form or paint with bright colors.

You can more clearly show how to make paths from tree cuts using a sectional drawing of a path.

Caring for wooden walkways

So that a self-made garden path made of saw cuts of a tree does not lose its original appearance over time, it needs constant care.

To do this, once a year you need to clean the saw cuts with a metal scraper, treat with an antiseptic and apply a special protective coating, drying oil or paint.

Advice
When you make a track, set aside a few cuts in reserve, in the future, it will be possible to replace individual elements during the repair process. In order to reduce the sliding effect after rain, do not polish the ends of the logs heavily before installation.

If you are interested in the process of arranging a path from tree cuts - a video illustrating DIY manufacturing

Garden paths from saw cuts of a tree - arguments "for"

• cheapness;
• high speed and ease of arrangement;
• the ability to carry out the entire process independently;
• do not accumulate moisture (do not create puddles);
• have a natural appearance;
• very maintainable;
• environmentally friendly;
• opportunity to make a unique garden path from wood. After all, all saw cuts are different, which means that it is impossible to repeat the pattern;
• the ability to use end-of-life logs as mulch or chop and add to compost.

Country paths from saw cuts of a tree - arguments "against"

• subject to decay;
• react to temperature changes;
• require constant care;
• become how many after the rain (leveled by using a special composition for processing).

Conclusion

Based on the foregoing, it becomes clear how to make a path from tree cuts with your own hands, without resorting to excessive costs and outside help. Although, you should not rely too much on cheapness, even with self-manufacturing you have to spend money, but such a path is worth it

The faster industry develops, the more man tries to get closer to nature. He surrounds himself with nature not literally, but by creating the illusion of being in the air, even if he is relaxing in the living room. This desire is not just to live in a house that is built from natural raw materials, but also to come up with an appropriate interior design. Therefore, everyone strives to use hand-made wood decor in their home in order to feel like a real owner.

The fashion for wood appeared a long time ago, but now not everyone can furnish their own home in the style of the Twin Peaks series. The room should not be oversaturated with wooden furniture, furs and animal heads. This already speaks of the bad taste of the owners. These blanks are available for the forest area, but for the steppe - decorating a house in this style will cost a pretty penny. There is an option to dilute the familiar environment with rare interspersed with wooden saw cuts, which pour into absolutely any image. You can create such a design yourself, spending only on fasteners.

Advantages of decorating the interior with wood saw cuts

The saw cuts of a tree surprise at the same time with their external attractiveness and the complexity of creating from a technical point of view.

Now let's figure out what advantages wood trim has:

• Durability. If the wood can be properly processed, and will be protected from moisture and various mechanical damage, then it will last a long time. If it's whole wooden wall or floor, then you can save on annual repairs.
• Thermal insulation. Firewood is a source of heat not only in a fire. The raw material has the ability to keep the temperature, so for a cold concrete apartment it is best view insulation, albeit partial. In winter, such an insulated floor will warm any legs.

decorative tree from branches

• Uniqueness. Of course, you can glue wallpaper with the image of tree cuts, or lay a laminate, but in such pictures a pattern is used - a simple repetition of one module. natural finish cuts is a composition where each element is unique. The pattern on the saw cut and its shape are unique.

Create a design wall

For decoration, it is advisable to choose one side of the room. The design of all planes is a sign of bad taste, and the room will look overloaded. Any room needs to be given air, and it's not about the windows. It should breathe space, and this effect is given by light empty planes. Only one “woody” facet of the room will become a kind of accent that will become its mood. You can lay out the "tree puzzle" yourself, and now let's talk about how it's done.

Everyone in the yard has an already withered tree that needs to be removed. Now it's time to cut it down. We take a branch, saw it into bars of medium thickness. From the resulting "pancakes" you can remove the bark, and then polish it. Thanks to this, you will not drive the thorn by touching the wall. The resulting wood layers should be processed special tool from insects, and then we put it on glue. It is advisable to varnish the resulting relief - varnished wood can last a long time.

On a note! Create a composition from branches of different sizes, starting from a massive trunk and ending with the thinnest branches. The composition breathes due to the formed voids between saw cuts of different sizes.

Wall panel - a piece of nature in the interior

You can meet a panel from any components, but you have not seen a canvas made of pieces of wood, right? Here, contrasts are welcome, so feel free to use even hemp. The picture should not look like a pattern, but a full-fledged composition with a dominant and secondary elements. Do tonal gradations, and place accents with the help of tone. Specifically for the proposed product, it is better to leave the bark - it will make it more attractive. The careless terrain will create the atmosphere of an endless forest, and move you into it.

It is advisable to sketch a rough sketch, but if you like to improvise directly in the course of work, then go ahead. For bright contrast assemble the frame of the canvas from simple planks, this will give the picture lightness. The saw cuts are sanded from the side that is adjacent to the wall for better bonding. Leave the other side untouched - this will give naturalness to the overall picture. Framed tree cuts in the interior will look like a window overlooking the forest. The frame collects the composition into one whole, and groups it.

Difficulties in laying out a modular floor

This type is quite complicated, so it is better to be patient and get to work. Choose thick trunks to avoid creating large voids when laying out circles. For the manufacture of the floor, hardwood logs are selected, because the floor is exposed daily.

There are two reasons that will make you sweat:

• Solution. If you put all the parts on glue, then the floor will not last long, even if you cover it all with varnish. Modules will fall off due to constant pressure. You will have to use a solution, possibly based on cement.
• Surface leveling. If the thickness of each element does not play a big role in the design of the vertical plane, then this is the main condition for the floor. It is necessary to adjust all the modules to the total thickness, and start grinding after installation. The procedure will take a lot of time, because it is not easy to achieve a smooth surface.

Next, start varnishing the finished surface. It will protect it from pests and external influences. The floor is easier to clean, and it will last longer in a “protected” state. An unprotected surface can be attacked by pests or simply begin to rot due to excessive moisture.

Creating home comfort with homemade furniture

Furniture looks completely different, depending on the type of raw materials available. Tables and chairs are made, since the silhouette of the cut itself already resembles a small table or chair.

There are two main principles for creating furniture:

• Modular - assembly of an element from small parts (modules). Actually, we are already familiar with this method. It allows you to create a product of absolutely any shape. It is also necessary to achieve a perfectly flat surface. Dishes will be placed on the table, and so that it does not turn over, the surface of the table must be perfectly sanded.

• Solid - a solid element is taken as the basis. This option is much simpler than the previous one in technical terms, but it is more difficult to find a bar with a large diameter. Things are better with chairs, and if you want a table at which the whole family would have dinner, you will have to tinker with finding a saw cut. large diameter. The price of the overall cut is quite large.

It doesn’t matter which principle you apply in creating a product, the main thing is to immediately evaluate your capabilities so as not to spoil the material. Any way is good, because wooden furniture renowned for its strength and durability.

Ideas for the kitchen based on semicircular cuts

Such a figure is an unusual piece of decor and a reliable assistant in the kitchen. The material withstands high temperatures and does not heat up so much. From saw cuts, you can create simple solid coasters and modular ones, the material of which is easier to find. Everyone saw such coasters in the store, and thought “No, you can’t do this yourself” - an erroneous opinion. Why pay more if you do it yourself?

The kitchen will be complemented by fancy semi-circular shelves that can be put together from solid wood cuts, dividing them into two parts. An illusion is created that the "kruglyashek" is in the process of sinking into the wall. The reception is interesting if the shelf is round, thanks to this, visual movement is created. The effect is achieved due to the dynamic relief on the bark. On the shelves harmoniously placed cookbooks, or personal collections of recipes of the hostess. And the product will withstand a sufficiently large weight, even if its dimensions may not inspire confidence.

Remember! If this is a stand specifically for dishes, then it is better to make it whole. Connecting small parts involves gluing, and glue is incompatible with high temperatures. The stand will simply fall apart into several pieces.

Wooden detail as an accent in the interior

Small inclusions of "forest" in the familiar environment mentally bring you closer to nature. Saw cuts in the interior are used as a decor, and perform certain functions.

We create fancy accents with our own hands:

• Watch. The unusual use of a wooden saw cut in any interior looks cute. Especially if it is an uneven circle with bark on the surface. The bark is fixed, because it is able to deteriorate over time. The more casually the wooden “pancake” looks, the more interesting the watch will turn out.

• Flower vases. Let your imagination run wild and use different kinds branches. An ornament made of small twigs created by oneself looks expensive, and no one will guess that the vase cost you a penny. It will be in harmony with the design, and will find a response in things with a similar decor.

Remember! There should be few things created from identical material in the room. They should overlap with each other, but not look like "brute force".

• Frames for mirrors. In creating a product, it is important to adhere to rhythm or metricity, but chaos will be inappropriate. Alternate large tree cuts with small ones, or make the entire frame from circles of approximate size. Either option will be correct.

It is quite possible to make a floor from saw cuts with your own hands. Not to mention small interior items that are made in a minute with wood, glue and your imagination. Surprise your friends with a tastefully decorated home and make your life more comfortable. It is an environmentally friendly product that will benefit your health. If the product is made of needles, then a slight coniferous aroma can even help you with the treatment of a cold.

If you can handle the floor, then decorating an entire wall with wood will seem like a matter of five minutes. You will need to use your own taste, and your knowledge of composition, although most people trust their instincts.

Everything will work out, it’s enough just to “assemble” these products and fix them with glue, or just cut out a solid object. Create an image in your head, and try to bring it to life. You do not need special knowledge or skills, follow the basic rules for choosing materials and processing tools. After all, why spend a lot of money on the work of a designer, if you are able to cope with this task on your own without spending a dime.

Floors are an important flooring in any space and can be made from different materials. Wood is considered environmentally friendly and attractive. Therefore, the floor is often formed from their own hands. It does not require the investment of numerous funds, and is also considered easy to create.

Features of this floor

Do-it-yourself wood cut floor in the photo looks attractive and interesting. Its creation involves the use of special "rounds", the thickness of which is equal to several centimeters. They are formed as a result of the cross-cutting of logs.

Due to their correct laying on the base, a bright, beautiful and unique surface on the floor is created. To fix the coating, various liquid materials are poured, most often polymers are used for this.

Pros of the floor

A do-it-yourself floor from wood cuts is created simply, but at the same time it has many advantages:

• an environmentally friendly coating is formed;
• it is possible to make a floor with minimal expenditure of money;
• you can take advantage of various unique opportunities to create a unique design, since it is allowed to use saw cuts from various logs that may have different or similar fragments;
• elements differ in shapes, colors or dimensions;
• such a decision is considered original for each house or apartment;
• it is easy to make a floor from wood cuts with your own hands, which significantly reduces the cost of creating a coating;
• floors are considered universal, therefore they are suitable for any interior and style.

Some people even prefer to use cracked logs, due to which a charming coating is obtained. But it is necessary to use only logs in which there are no signs of disease or decay.

Flaws

There are some drawbacks to this floor. It is important to choose fragments that have the same thickness. If mistakes are made in technology, this will cause the creation of floors that do not have high strength and durability.

What kind of logs can be used?

Not all elements are suitable for this process, as some requirements for them are taken into account:

• too soft logs are not used for the procedure;
• it is important to select saw cuts obtained as a result of processing hardwood;
• saw cuts of spruce, pine or aspen are not suitable for these purposes, therefore the best choice there will be walnut or oak;
• the financial capabilities of buyers are also taken into account, since natural wood is expensive.

If you use expensive wood species, then the design will last a long time and will look luxurious.

How to make a floor?

Do-it-yourself floor from wood cuts is created step by step simply and quickly in time. For this, the following steps are performed:

• the procedure is similar to laying paving slabs, so initially you need to carefully prepare the base, which must be well-compacted, even and solid;
• a layer of river pebbles is laid on top of it, and its thickness should vary from 6 to 10 cm;
• further, the saw cuts are directly laid, for which they are adjusted using a rubber hammer;
• it is important to constantly check the correct location of each element with a level, which will avoid the presence of distortions and other problems on the coating;
• between the cuts there is a distance not exceeding 1.5 cm;
• then the joints between the elements are filled, the mixture for this can be bought at ready-made or make it yourself using clay, lard, lime and sawdust;
• often selected polymer compositions of high quality;
• the mixture is introduced into the seams between the saw cuts, after which it is well rubbed, it is important to make sure that there are no pockets of air, and if voids remain, they can cause cracks or water penetration under the floor;
• the procedure for filling the sutures is repeated after two days.

Thus, according to right technology Do-it-yourself floors from wood cuts are formed very simply, and at the same time, a high-quality and attractive design is obtained in any room.

What to do after creating the floor?

As soon as the floor is made from wood cuts with your own hands, you should polish it well. It is optimal to use a sanding machine for this, and after grinding it is necessary to check the coating for cracks. If they are absent, then at the end is done manual grinding. After the floor dries, polishing begins; for an environmentally friendly coating, it is better to use wax or linseed oil.

The floor from saw cuts is considered interesting choice for any room. It has huge advantages, although it also has disadvantages. It is considered easy to create, therefore, due to your own efforts and small financial investments, you can get an original and unique design on the floor.

The saw cut floor is made of natural materials that do not have any negative health effects. Due to the fact that it is made from natural resources

Benefits of saw cut floors:

The saw cut floor is made from natural materials that do not have any negative health effects.
Due to the fact that it is made from natural resources, it can be very cheap.
Contrary to the opinion of skeptics, such a floor is more durable than expected.
Exceptional aesthetic appearance and pleasant to the touch.
Easily done without the need to hire a specialist.

Flaws:

Unfortunately this is the type floor covering requires quite a lot of good quality wood, so it is recommended to cover only small areas (to protect forests).
Require frequent Maintenance(every 2 years)

Construction stages:

Before proceeding with the creation of such a floor, it is very important to read information about natural houses, floors in which can be not only inexpensive and healthy, but also very effective, because they form a thermal mass and act as a heat storage from sunlight or any other source of energy.

Materials:

Pieces of logs are about 10-12 cm thick (the diameter may differ from everyone's imagination).
Sawdust, limestone, clay, linseed oil, beeswax, water, lard.

Note: it is important that the cuts are very, very well dried (not to mention work, no moisture).

The process of making such a floor is relatively simple and is very similar to laying paving slabs or paving stones. You need a hard, well-packed surface, on top of which we pour a layer of river pebbles (about 6-10 cm). Then, using a rubber mallet, we proceed to laying the saw cuts. We tap and check with a level that the floor is even and none of the saw cuts stick out or go too deep. As a rule, after laying, the distance from the surface of the cuts to the level of the sand is about 4-7 cm, and the distance between the cuts should be approximately one to one and a half centimeters.

Joint filler mix:

For a floor area of ​​about 5 square meters, in a 15-liter bucket for 1 kg of melted pork fat, add 1 kg of lime, 5 kg of sawdust and 2 kg of clay with water. After thorough mixing, you should get a pasty mass. You can also add marble dust or glass shards with grease to help make the mixture waterproof.

We introduce the mixture into the distances between the cuts and rub it well, as far as possible, without leaving air pockets. It should fill the gaps up to the magazines. It is very important that there are no voids left, otherwise cracks and water leakage cannot be avoided in the future. Residues of this mixture can also be used to fill cracks in saw cuts (if applicable). After the last seam is smeared, we leave our floor to dry for 1-2 days. Check if you have cracks, then fill them. After complete drying (another day or two) it is well polished. Even scraping is recommended. You can rent a cycling machine to achieve the perfect effect. After that, once again carefully, very carefully check if you have any cracks. If found, fill in gaps, hand sand and leave to dry completely. This usually shouldn't happen after scraping, but especially if you're using a bathroom floor like this, it never hurts to be more careful.

And finally, it's time for the most pleasant stage of finishing. Since our floor is made of natural materials, we will polish it with natural materials, namely beeswax and linseed oil.